Descripción
CO/PRO 3DA1 Dual-Sensor Carbon Monoxide Shutoff Switch
Two independent sensors with automatic appliance shutoff at 25 ppm
The CO/PRO 3DA1 is an automatic carbon monoxide shutoff switch that connects to new and existing furnaces and tank-based water heaters. Two independent CO sensors monitor the air at the same time: one in the HVAC supply duct and one in the ambient air near the appliance's exhaust system. If either sensor reads 25 ppm or more, the CO/PRO cuts power to the connected appliance. That stops CO at the source. When levels drop to 15 ppm or less, it restores power automatically.
Standard CO detectors sound an alarm only after CO has spread through the home. They're typically designed to alarm at 70 ppm and can take 1 to 4 hours to do so. The CO/PRO acts much earlier, right where CO is produced. It runs a daily self-test on each sensor and alerts you when a sensor reaches end of life. It has a digital display, an audible alarm and visual indicators. The CO/PRO mounts on the supply duct or on a wall, and installation averages about 15 minutes.
CaracterÃsticas y ventajas principales
- Dual sensors monitor supply duct air (D) and ambient air (A) at the same time
- Either sensor can trigger automatic shutoff of connected appliances
- Turns off fuel-burning appliances when CO reaches 25 ppm or more
- Restores power to appliances when CO drops to 15 ppm or less
- Connects to new and existing furnaces and water heaters
- Two factory-calibrated, UL-2075 compliant sensors with up to 10-year life
- Automatic daily self-test with sensor end-of-life alert
- Digital display with audible alarm and visual indicators
- Duct mount or wall mount
- Average 15-minute installation
- 24 VAC powered
- Multi-patented operation
- 1-year warranty (2 years when registered)
- Made in the USA using imported components
Note: The CO/PRO is a CO monitor and shutoff switch. It works alongside installed CO alarms and detectors required by code and does not replace them. It requires professional installation.
CaracterÃsticas técnicas
| CO/PRO 3DA1 Carbon Monoxide Shutoff Specs | |
|---|---|
| Sensores | Two independent, UL-2075 compliant (Supply Duct and Ambient) |
| CO Alarm / Shutoff Level | 25 ppm or greater |
| CO Relay Reset Level | 15 ppm or less |
| CO Sensor / Display Range | 0 - 99 ppm |
| Precisión | ±5 ppm @ 0 - 25 ppm, ±10 ppm @ 26 - 100 ppm |
| Tiempo de respuesta | 90 seconds (10% to 90% of range) |
| Alarma sonora | ~71 dB @ 3 ft |
| Potencia | 20 - 30 VAC, less than 5 Watts |
| Relays | Two Dry SPDT-NC (Form B), 5A 24 VAC |
| Mounting Location | Supply duct, 6 ft from duct bend/source (wall mount optional) |
| Vida útil del sensor | Up to 10 years |
| Temperatura de funcionamiento | 60°F to 158°F (15°C to 70°C) |
| Temperatura de almacenamiento | -4°F to 158°F (-20°C to 70°C) |
| Relative Humidity | 5 - 99%, non-condensing |
| Case | Polycarbonate, UL94 V0 |
| Dimensiones | 3.5" W x 6.3" H x 9.7" D (89 x 160 x 246 mm) |
| GarantÃa | 1 Year (2 Years when registered) |
Incluye
- (1) CO/PRO 3DA1 Carbon Monoxide Shutoff Switch
- (1) Duct Tube/Mounting Plate
- (2) Mounting Screws
- (1) Informational Sticker