Ace Chem Pro AceSeal EZ Leak Stop Pro+ with UV Dye for 1.5 to 5 Ton Systems

Ace Chem Pro AceSeal EZ Leak Stop Pro+ with UV Dye for 1.5 to 5 Ton Systems

Permanently seal more, larger leaks — Improves A/C performance for 1.5 to 5 ton systems

AceSeal Pro+ with UV Dye is a concentrated refrigerant leak sealant supplied with a special hose injection delivery system that makes it simple, fast, and easy to use while also locating larger leaks. The product is a combination of POE oil and various polar additives in a uniform blend which is compatible with all refrigerants except ammonia. AceSeal products are ideal for use in heat pumps, split and mini- split units, packaged units, microchannel coils, coolers, and commercial units. AceSeal travels with the gas, which makes it faster, and more effective at finding leaks.

Key Features & Benefits

• Seals leaks up to 30 mm
• More concentrated formula
• Permanently seals leaks in A/C & refrigeration systems
• UV dye helps to locate larger leaks
• Compatible with all oils & refrigerants, except ammonia
• No need to pump down R410, or other units
• Easy installation just connect and inject, no additional tools needed
• Proven formula with millions of units sealed

---

Instructions for Use: Turn the AC/R system on and verify the unit is running. Connect AceSeal to the low side service port of the system (generally the large line). Connect the manifold refrigerant hose to the refrigerant supply tank. Verify the high side and low side valves on the manifold are closed before proceeding. Purge the low pressure hose when connecting to the AceSeal. Open the low side valve and watch for the hose to clear. Turn off the low side manifold as soon as the hose clears. Turn off the refrigerant gas. Verify the system is charged to the manufacturer's specifications. Disconnect the low side hose from AceSeal. Install service port cap. Run A/C unit for at least one hour after installation complete.
Note: Use a refrigerant cylinder to push sealant into system while charging if the system is low on refrigerant. Simply connect AceSeal to service port and inject refrigerant through injector into system while charging. When using AceSeal with UV Dye, in event system continues to lose refrigerant, use a UV light to locate the source of the leak. When located, clean and repair leak site. Always wear protective glasses when using UV light.

---

AceSeal Pro FAQ's

1. Can I inject AceSeal EZ Leak Stop Pro into a system while charging with refrigerant?
   Yes, you can use the refrigerant to push the sealant into the low side of the system.
2. How large a leak will AceSeal EZ Leak Stop Pro repair?
   As a guide, if the system loses more than 15% of its charge within a week, the leak is too large to seal.
3. Can I refill the AceSeal EZ Leak Stop Pro Inject?
   AceSeal EZ Leak Stop Pro Inject is a one-time, one-application use.
4. Will AceSeal EZ Leak Stop Pro clog Schrader valves?
   AceSeal EZ Leak Stop Pro will seal the Schrader valve if it is leaking. However, when reconnecting the charging hose, the seal will be broken, allowing the Schrader valve to be used normally.
5. Will AceSeal EZ Leak Stop Pro blend with all refrigerants?
   AceSeal EZ Leak Stop Pro mixes with all hydrocarbon and chemical (R12, R134a, R502, R22) refrigerants. Do not use in ammonia systems.
6. Will AceSeal EZ Leak Stop Pro work in all systems?
   AceSeal EZ Leak Stop Pro Inject will seal most leaks when used according to the manufacturer's directions. It will seal most small holes located in the air-conditioning condenser, evaporator, fittings, and metal lines. It will not repair O-rings or seals. Do not use in ammonia systems.
7. Should I pump down the system to get AceSeal Leak Stop Inject into the system?
   Pump down of the system is not necessary with AceSeal Leak Stop Inject, regardless of the type of refrigerant being used.